Dell Inspiron 7591 2-in-1 Скачать руководство пользователя страница 75

Страница: 75 / 80

Maintenance

BIOS Auto-Recovery

Enables the computer to automatically recover the BIOS without user actions. This
feature requires BIOS Recovery from Hard Drive to be set to Enabled.

Default: OFF.

Start Data Wipe

CAUTION:

This Secure Wipe Operation will delete information in a way

that it cannot be reconstructed.

If enabled, the BIOS will queue up a data wipe cycle for storage devices that are
connected to the motherboard on the next reboot.

Default: OFF.

Allow BIOS Downgrade

Controls flashing of the system firmware to previous revisions.

Default: ON.

Table 16. System setup options—System Logs menu

System Logs

Power Event Log

Displays Power events.

Default: Keep.

BIOS Event Log

Displays BIOS events.

Default: Keep.

Thermal Event Log

Displays Thermal events.

Default: Keep.

Table 17. System setup options—SupportAssist menu

SupportAssist

Dell Auto operating system Recovery
Threshold

Controls the automatic boot flow for SupportAssist System Resolution Console and
for Dell operating system Recovery tool.

Default: 2.

SupportAssist operating system Recovery

Enables or disables the boot flow for SupportAssist operating system Recovery tool
in the even of certain system errors.

Default: ON.

System and admin password

Table 18. System and admin password

Password type

Description

System password

Password that you must enter to log on to your computer.

Admin password

Password that you must enter to enable some security features in
your computer.

You can create a system password and a admin password to secure your computer.

CAUTION:

The password features provide a basic level of security for the data on your computer.

CAUTION:

Anyone can access the data stored on your computer if it is not locked and left unattended.

NOTE:

System and admin password feature is disabled.

System setup

Содержание Inspiron 7591 2-in-1

















































































Результаты поиска

Содержание Inspiron 7591 2-in-1

Отзывы:

Похожие инструкции для Inspiron 7591 2-in-1

Бренды по названию

Популярные бренды

Dell Inspiron 7591 2-in-1, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 7591 2-in-1

Отзывы:

Похожие инструкции для Inspiron 7591 2-in-1

Бренды по названию

Популярные бренды