Dell Inspiron 7591 2-in-1 Скачать руководство пользователя страница 43

Страница: 43 / 80

Post-requisites

1. Replace the

battery

2. Replace the

base cover

Heat sink

Removing the heat sink

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

NOTE:

The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you

touch it.

CAUTION:

For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The oils in your

skin can reduce the heat transfer capability of the thermal grease.

Prerequisites

1. Remove the

base cover

2. Remove the

fan

Procedure

1. In reverse order (as indicated on the heat sink), loosen the four captive screws that secure the heat sink to the system board.
2. Lift the heat sink off the system board.

Removing and installing components

Содержание Inspiron 7591 2-in-1

















































































Результаты поиска

Содержание Inspiron 7591 2-in-1

Отзывы:

Похожие инструкции для Inspiron 7591 2-in-1

Бренды по названию

Популярные бренды

Dell Inspiron 7591 2-in-1, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 7591 2-in-1

Отзывы:

Похожие инструкции для Inspiron 7591 2-in-1

Бренды по названию

Популярные бренды