Dell Inspiron 5680 страница 93 Скачать руководство пользователя

Страница: 93 / 130

Replacing the power-supply unit

WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in

Before

working inside your computer

. After working inside your computer, follow

the instructions in

After working inside your computer

. For more safety best

practices, see the Regulatory Compliance home page at

www.dell.com/

regulatory_compliance

Procedure

Place the power supply on the chassis.

Slide the power-supply unit towards the back of the chassis until it snaps into
place.

Align the screw holes on the power-supply unit with the screw holes on the
chassis.

Replace the four screws (6-32UNCx6.3) that secure the power-supply unit to
the chassis.

Route the power-supply unit cables through the routing guides on the chassis.

Connect the power cables to their extensions.

Connect the processor-power cable and system-board power cable to the
system board.

Connect the power cables to the hard drives and optical drive.

NOTE: For computers with graphics card, connect the power cable to
the graphics card, if applicable.

Place the computer in an upright position.

Post-requisites

Replace the

right-side cover

Содержание Inspiron 5680



































































































































Результаты поиска

Содержание Inspiron 5680

Отзывы:

Похожие инструкции для Inspiron 5680

Бренды по названию

Популярные бренды

Dell Inspiron 5680, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 5680

Отзывы:

Похожие инструкции для Inspiron 5680

Бренды по названию

Популярные бренды