Dell Inspiron 5521 Скачать руководство пользователя страница 87

Страница: 87 / 118

Sensor board

Removing the sensor board

Prerequisites

1. Follow the procedure in

Before working inside your computer

2. Enter

3. Remove the

4. Remove the

5. Remove the

6. Remove the

7. Remove the

8. Remove the

9. Remove the

10. Remove the

About this task

NOTE:

This procedure applies only to computers shipped with a sensor board.

The following images indicate the location of the sensor board and provide a visual representation of the removal procedure.

Steps

1. Open the latch and disconnect the LED cable from connector on the sensor board.
2. Gently lift the sensor board away from the display back cover.

Installing the sensor board

About this task

The following images indicate the location of the sensor board and provide a visual representation of the removal procedure.

Removing and installing components

Содержание Inspiron 5521























































































































Результаты поиска

Содержание Inspiron 5521

Отзывы:

Бренды по названию

Популярные бренды

Dell Inspiron 5521, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 5521

Отзывы:

Бренды по названию

Популярные бренды