manualshive.com logo in svg

Dell Inspiron 5521, Руководство по обслуживанию

Поделиться
Скачать
Dell Inspiron 5521 Скачать руководство пользователя страница 50

Steps

1. Remove the two (M2x4) screws that secure the system fan to the frame.
2. In reverse sequential order (as indicated on the heat sink), loosen the six (M2x3) screws that secure the heat sink and fan

assembly to the system board.

3. Disconnect the fan cable from the connector on the system board.
4. Lift the heat sink and fan assembly off the system board.

Installing the heat sink and fan assembly - Discrete configuration

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

CAUTION:

 Incorrect alignment of the heat sink can damage the system board and processor.

NOTE:

 If either the system board or the heat sink is replaced, use the thermal pad/paste provided in the kit to ensure that

thermal conductivity is achieved.

About this task

The following image indicates the location of the heat sink and fan assembly for a system with discrete configuration and
provides a visual representation of the installation procedure.

50

Removing and installing components

Содержание Inspiron 5521























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды