Dell Inspiron 3782 Скачать руководство пользователя страница 63

Страница: 63 / 99

Replacing the display assembly

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

Procedure

NOTE:

Ensure that the hinges are opened to the maximum before replacing the display assembly on palm-rest and

keyboard assembly.

1. Slide the palm-rest and keyboard assembly under the hinges on the display assembly and close it.

2. Using the alignment posts, press the hinges down on the system board and the palm-rest and keyboard assembly.
3. Replace the five screws (M2.5x5) that secure the left and right hinges to the system board and palm-rest and keyboard assembly.

Replacing the display assembly

Содержание Inspiron 3782




































































































Результаты поиска

Содержание Inspiron 3782

Отзывы:

Похожие инструкции для Inspiron 3782

Бренды по названию

Популярные бренды

Dell Inspiron 3782, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 3782

Отзывы:

Похожие инструкции для Inspiron 3782

Бренды по названию

Популярные бренды