Dell Inspiron 3782 Скачать руководство пользователя страница 23

Страница: 23 / 99

Replacing the base cover

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

Procedure

1. Connect the battery cable to the system board, if applicable.

CAUTION:

To avoid accidental damage to the power-adapter port, do not press the base cover against the power-

adapter port when you snap the base cover to the computer base.

2. Place the base cover on the palm rest and keyboard assembly, and snap the base cover into place starting from the power-adapter

port.

Replacing the base cover

Содержание Inspiron 3782




































































































Результаты поиска

Содержание Inspiron 3782

Отзывы:

Похожие инструкции для Inspiron 3782

Бренды по названию

Популярные бренды

Dell Inspiron 3782, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 3782

Отзывы:

Похожие инструкции для Inspiron 3782

Бренды по названию

Популярные бренды