Dell Inspiron 3490 Скачать руководство пользователя страница 36

Страница: 36 / 86

Replacing the touchpad

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

Procedure

NOTE:

Ensure that the touchpad is aligned with the guides available on the palm-rest and keyboard assembly, and the

gap on either sides of the touchpad is equal.

1. Place the touchpad into the slot on the palm rest and keyboard assembly.
2. Replace the four screws (M2x2) that secure the touchpad to the palm rest and keyboard assembly.

Removing and installing components

Содержание Inspiron 3490























































































Результаты поиска

Содержание Inspiron 3490

Отзывы:

Похожие инструкции для Inspiron 3490

Бренды по названию

Популярные бренды

Dell Inspiron 3490, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 3490

Отзывы:

Похожие инструкции для Inspiron 3490

Бренды по названию

Популярные бренды