Dell Inspiron 24 5410 All-in-One Скачать руководство пользователя

Страница: 15 / 87

Insert the stands into the slots on the back cover until they snap into place on the display-assembly base.

Next steps

Follow the procedure in

After working inside your computer

Back cover

Removing the back cover

Prerequisites

1. Follow the procedure in

Before working inside your computer

CAUTION:

When servicing the computer, place it on an elevated, clean and flat surface. Place the display

flat on the surface with the stand hanging over the edge. It is recommended to remove the stand to avoid
accidental damage to the computer display when servicing.

About this task

The following image indicates the location of the back cover and provides a visual representation of the removal procedure.

Removing and installing components

Содержание Inspiron 24 5410 All-in-One
























































































Результаты поиска

Содержание Inspiron 24 5410 All-in-One

Отзывы:

Похожие инструкции для Inspiron 24 5410 All-in-One

Бренды по названию

Популярные бренды

Dell Inspiron 24 5410 All-in-One, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 24 5410 All-in-One

Отзывы:

Похожие инструкции для Inspiron 24 5410 All-in-One

Бренды по названию

Популярные бренды