manualshive.com logo in svg

Dell Inspiron 17 7000 Series, Руководство по обслуживанию

Поделиться
Скачать
Dell Inspiron 17 7000 Series Скачать руководство пользователя страница 49

Replacing the status-light board

WARNING: Before working inside your computer, read the safety 
information that shipped with your computer and follow the steps in 

Before 

working inside your computer

. After working inside your computer, follow 

the instructions in 

After working inside your computer

. For more safety best 

practices, see the Regulatory Compliance home page at 

www.dell.com/

regulatory_compliance

.

 

Procedure

1 

Place the status-light board into the slot on the palm-rest assembly.

2 

Adhere the foam that secures the status-light board to the palm-rest assembly.

3 

Slide the status-light board cable into the connector on the system board and 
close the latch to secure the cable.

4 

Route the speaker cable through the routing guides on the palm-rest assembly.

Post-requisites

1 

Replace the 

battery

.

2 

Replace the 

base cover

.

49

Содержание Inspiron 17 7000 Series





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды