Dell Inspiron 15 Gaming Скачать руководство пользователя страница 76

Страница: 76 / 112

Removing the heat sink

WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in

Before working inside your computer

. After working inside your

computer, follow the instructions in

After working inside your

computer

. For more safety best practices, see the Regulatory

Compliance home page at

www.dell.com/regulatory_compliance

WARNING: The heat sink may become hot during normal operation.
Allow sufficient time for the heat sink to cool before you touch it.

CAUTION: For maximum cooling of the processor, do not touch the

heat transfer areas on the heat sink. The oils in your skin can reduce

the heat transfer capability of the thermal grease.

Prerequisites

Remove the

Remove the

Remove the

Remove the

Remove the

Remove the

Follow the procedure from step 1 to step 8 in “

Removing the palm rest

and keyboard assembly

”.

Remove the

fans

Remove the

system board

Procedure

NOTE: The appearance of the heat sink on your computer may differ

from the image shown in this chapter.

In sequential order (indicated on the heat-sink), remove the six screws

(M2x3) that secure the heat sink to the system board.

Содержание Inspiron 15 Gaming

















































































































Результаты поиска

Содержание Inspiron 15 Gaming

Отзывы:

Похожие инструкции для Inspiron 15 Gaming

Бренды по названию

Популярные бренды

Dell Inspiron 15 Gaming, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 15 Gaming

Отзывы:

Похожие инструкции для Inspiron 15 Gaming

Бренды по названию

Популярные бренды