Dell Inspiron 15 3525 Скачать руководство пользователя страница 44

Страница: 44 / 97

About this task

NOTE:

The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you

touch it.

NOTE:

For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The oils in your skin

can reduce the heat transfer capability of the thermal grease.

The following images indicate the location of the UMA heat sink and provide a visual representation of the removal procedure.

Steps

1. Loosen the four captive screws that secure the heat sink to the system board.

NOTE:

Loosen the captive screws in the reverse sequential order mentioned on the heat sink [4 > 3 > 2 > 1].

NOTE:

The number of screws varies depending on the configuration ordered.

2. Lift the heat sink from the system board.

Installing the heat sink - UMA

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

NOTE:

If either the system board or the heat sink is replaced, use the thermal grease provided in the kit to ensure that

thermal conductivity is achieved.

The following images indicate the location of the UMA heat sink and provide a visual representation of the installation
procedure.

Removing and installing components

Содержание Inspiron 15 3525


































































































Результаты поиска

Содержание Inspiron 15 3525

Отзывы:

Похожие инструкции для Inspiron 15 3525

Бренды по названию

Популярные бренды

Dell Inspiron 15 3525, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 15 3525

Отзывы:

Похожие инструкции для Inspiron 15 3525

Бренды по названию

Популярные бренды