Dell Inspiron 15 3525 Скачать руководство пользователя страница 25

Страница: 25 / 97

Steps

1. Using your fingertips, carefully spread apart the securing-clips on each end of the memory-module slot until the memory

module pops-up.

2. Remove the memory module from the memory-module slot on the system board.

NOTE:

Your computer may have up to two memory modules installed. Repeat steps 1 to 2 if there is a second memory.

module installed.

Installing the memory modules

Prerequisites

If you are replacing a component, remove the existing component before performing the installation process.

About this task

The following images indicate the location of the memory modules and provide a visual representation of the installation
procedure.

Removing and installing components

Содержание Inspiron 15 3525


































































































Результаты поиска

Содержание Inspiron 15 3525

Отзывы:

Похожие инструкции для Inspiron 15 3525

Бренды по названию

Популярные бренды

Dell Inspiron 15 3525, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 15 3525

Отзывы:

Похожие инструкции для Inspiron 15 3525

Бренды по названию

Популярные бренды