Dell Inspiron 15 3000 Series Скачать руководство пользователя страница 64

Страница: 64 / 115

Removing the heat sink

WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in

Before

working inside your computer

. After working inside your computer, follow

the instructions in

After working inside your computer

. For more safety best

practices, see the Regulatory Compliance home page at

www.dell.com/

regulatory_compliance

WARNING: The heat sink may become hot during normal operation. Allow
sufficient time for the heat sink to cool before you touch it.

CAUTION: For maximum cooling of the processor, do not touch the heat
transfer areas on the heat sink. The oils in your skin can reduce the heat
transfer capability of the thermal grease.

Prerequisites

Remove the

battery

Follow the procedure from step 1 to step 3 in “

Removing the optical drive

”.

Remove the

keyboard

Follow the procedure from step 1 to step 7 in “

Removing the base cover

”.

Procedure

Remove the captive screws that secure the heat sink to the system board.

Содержание Inspiron 15 3000 Series




















































































































Результаты поиска

Содержание Inspiron 15 3000 Series

Отзывы:

Похожие инструкции для Inspiron 15 3000 Series

Бренды по названию

Популярные бренды

Dell Inspiron 15 3000 Series, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 15 3000 Series

Отзывы:

Похожие инструкции для Inspiron 15 3000 Series

Бренды по названию

Популярные бренды