manualshive.com logo in svg

Dell Inspiron 13 7000 2-in-1, Руководство по обслуживанию

Поделиться
Скачать
Dell Inspiron 13 7000 2-in-1 Скачать руководство пользователя страница 129

4 

Select or clear the 

Enable External USB Port 

check box to enable or 

disable it respectively.

5 

Save the BIOS setup program settings and exit.

Fixing a no-boot issue caused by USB emulation

Sometimes the computer does not boot to the operating system when USB 
devices are connected to the computer during startup. This behavior occurs 
because the computer is looking for bootable files in the USB devices. Follow 
these steps to fix the no-boot issue:

1 

Turn on or restart your computer.

2 

Press F2 when the Dell logo is displayed on the screen to enter the BIOS 

setup program.
The BIOS setup program is displayed.

3 

On the left pane, select 

Settings

 → 

System Configuration

 → 

USB 

Configuration

.

The USB configuration is displayed on the right pane.

4 

Clear the 

Enable Boot Support

 check box to disable it.

5 

Save the settings and exit.

Wi-Fi

The Inspiron 17-7778 is shipped with Wi-Fi 802.11ac.

Turning on or off Wi-Fi

NOTE: There is no physical switch to enable or disable Wi-Fi. It has to be 

done through computer settings.

1 

Swipe-in from the right edge of the display, or click or tap the 

Action 

Center

 icon on the taskbar to access the Action Center.

2 

Click or tap 

Wi-Fi 

to turn Wi-Fi on or off.

Downloading the Wi-Fi driver

1 

Turn on your computer.

2 

Go to 

www.dell.com/support

.

129

Содержание Inspiron 13 7000 2-in-1


























































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды