Dell G7 7700 Скачать руководство пользователя страница 24

Страница: 24 / 96

Memory modules

Removing the memory modules

Prerequisites

1. Follow the procedure in

Before working inside your computer

2. Remove the

base cover

About this task

The following image indicates the location of the memory modules and provides a visual representation of the removal procedure.

Steps

1. Use your fingertips to carefully spread apart the securing-clips on each end of the memory-module slot until the memory module pops

up.

2. Slide and remove the memory module from the memory-module slot.

NOTE:

Repeat step 1 and step 2 to remove the other memory module, if installed on your computer.

Installing the memory modules

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following image indicates the location of the memory modules and provides a visual representation of the installation procedure.

Removing and installing components

Содержание G7 7700

































































































Результаты поиска

Содержание G7 7700

Отзывы:

Dell G7 7700, Руководство по обслуживанию, Страница: 24 / 96

Результаты поиска

Содержание G7 7700

Отзывы: