Dell G16 7620 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 79

Dell G16 7620 Скачать руководство пользователя страница 35

8. Connect the DDS (Dynamic Display Switch) cable to the system board.

Next steps

1. Install the

.

2. Install the

.

3. Follow the procedure in

After working inside your computer

.

Keyboard-controller board

Removing the keyboard-controller board

Prerequisites

1. Follow the procedure in

Before working inside your computer

.

2. Remove the

.

3. Remove the

.

About this task

The following image(s) indicate the location of the keyboard-controller board and provides a visual representation of the
removal procedure.

Steps

1. Open the latch and disconnect the keyboard-backlight cable from the keyboard-controller board.
2. Open the latch and disconnect the keyboard cable from the keyboard-controller board.
3. Open the latch and disconnect the keyboard-controller board cable from the system board.
4. Remove the screw (M2x2) that secures the keyboard-controller board to the palm-rest and keyboard assembly.
5. Lift the keyboard-controller board off the palm-rest and keyboard assembly.

Removing and installing components

35

«
...
33
34
35
36
37
...
»

Содержание G16 7620
















































































Отзывы:

Нет отзывов