Dell EMC PowerEdge T440 Скачать руководство пользователя

Страница: 19 / 156

Item

Ports, panels, or slots

Icon

Description

NIC port (2)

The NIC ports are integrated on the system board provide network

connectivity. For more information about the supported configurations,

see the Technical specifications section.

USB 2.0 port (4)

The USB ports are 4-pin, 2.0-compliant. These ports enable you to

connect USB devices to the system.

USB 3.0 port (2)

The USB ports are 9-pin and 3.0-compliant. These ports enable you to

connect USB devices to the system.

VGA port

Enables you to connect a display device to the system. For more

information, see the Technical specifications section.

Serial port

Enables you to connect a serial device to the system. For more

information, see the Technical specifications section.

System identification button

The System Identification (ID) button is available on the front and back of

the systems. Press the button to identify a system in a rack by turning on

the system ID button. You can also use the system ID button to reset

iDRAC and to access BIOS using the step through mode.

External cooling fan
(optional)

N/A

Enables you to connect an optional redundant cooling fan.

PCIe expansion card slot(6) N/A

The expansion slot(s) enable you to connect PCI Express expansion
cards. For more information on the expansion cards that are supported
on your system, see the Expansion card guidelines.

Содержание EMC PowerEdge T440





























































































































































Результаты поиска

Содержание EMC PowerEdge T440

Отзывы:

Похожие инструкции для EMC PowerEdge T440

Бренды по названию

Популярные бренды

Dell EMC PowerEdge T440, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EMC PowerEdge T440

Отзывы:

Похожие инструкции для EMC PowerEdge T440

Бренды по названию

Популярные бренды