Dell ECS EX Series Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 112

background image

Figure 9. EX500 server chassis front view

LED indicators are on the left and right side of the server front panels.

Figure 10. Left control panel

The left control panel LED behavior is broken into two subsets, the light bar and the status LEDs. The light bar also functions as
a button. The light bar indicates chassis health and also functions as System ID when pressed.

Table 9. Decoding of LEDs in light bar

Status

ID button

Indicates that the system is turned on, system is healthy, and
system ID mode is not active. Press the system health and
system ID button to switch to system ID mode.

Solid Blue

Indicates that the system is in fail-safe mode. If the problem
persists, see the Getting help section.

Solid Amber

Indicates that the system is experiencing a fault. Check
the System Event Log for specific error messages. For
information about the event and error messages generated
by the system firmware and agents that monitor system
components, see the Error Code Lookup page at

Blink Amber

Indicates that the system ID mode is active. Press the system
health and system ID button to switch to system health mode.

Blink Blue

There are two status LEDs to indicate and identify any failed hardware components.

EX500 Platform

23

«
...
21
22
23
24
25
...
»

Содержание ECS EX Series

















































































































Отзывы:

Нет отзывов

Похожие инструкции для ECS EX Series

FusionServer 5288 V6

Бренд: xFusion Digital Technologies Страницы: 131

Бренд: Conceptronic Страницы: 127

Бренд: HIKVISION Страницы: 13

Бренд: Asus Страницы: 186

Бренд: Antrica Страницы: 68

Бренд: QNAP Страницы: 203

Бренд: netAlly Страницы: 2

Бренд: Aviosys Страницы: 30

Бренд: pachanko Страницы: 56

Бренд: Meinberg Страницы: 170

Бренд: Planet Networking & Communication Страницы: 67

Бренд: Planet Networking & Communication Страницы: 76

Бренд: Z Microsystems Страницы: 21

Rackable C2005 2U

Бренд: Silicon Graphics Страницы: 46

Бренд: Silicon Graphics Страницы: 162

Бренд: Mirapoint Страницы: 98

TimeProvider 5000

Бренд: Symmetricom Страницы: 534

Бренд: XVision Страницы: 100

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды