Dell E70S Скачать руководство пользователя страница 88

Страница: 88 / 238

Figure 87. Installing the 2 x 2.5-inch rear drive module

Next steps

1. Connect all the cables to the rear drive module.
2.

Install the drives

3. If removed,

install the air shroud

4. Follow the procedure listed in

After working inside your system

Drive backplane

This is a service technician replaceable part only.

Drive backplane

Depending on your system configuration, the drive backplanes supported are listed here:

Table 42. Supported backplane options

System

Supported hard drives options

PowerEdge R750

2.5-inch (x 8) NVMe backplane

3.5-inch (x 12) SAS or SATA backplane

2.5-inch (x 16) SAS, SATA or NVMe backplane (2 x 8 NVMe)

2.5-inch (x 24) SAS, SATA, NVMe backplane

Installing and removing system components

Содержание E70S















































































































































































































































Результаты поиска

Содержание E70S

Отзывы:

Похожие инструкции для E70S

Бренды по названию

Популярные бренды

Dell E70S, Инструкция по установке и обслуживанию

Результаты поиска

Содержание E70S

Отзывы:

Похожие инструкции для E70S

Бренды по названию

Популярные бренды