Dell E70S Скачать руководство пользователя страница 205 | Manualshive

Страница: 205 / 238

background image

Restoring the system using Easy Restore

The Easy Restore feature enables you to restore your service tag, license, UEFI configuration, and the system configuration data
after replacing the system board. All data is backed up in a backup flash device automatically. If BIOS detects a new system
board, and the service tag in the backup flash device, BIOS prompts the user to restore the backup information.

About this task

Below is a list of options/steps available:

●

Restore the service tag, license, and diagnostics information, press

Y

●

Navigate to the Lifecycle Controller based restore options, press

N

●

Restore data from a previously created

Hardware Server Profile

, press

F10

NOTE:

When the restore process is complete, BIOS prompts to restore the system configuration data.

●

Restore data from a previously created

Hardware Server Profile

, press

F10

●

To restore the system configuration data, press

Y

●

To use the default configuration settings, press

N

●

NOTE:

After the restore process is complete, system reboots.

Manually update the Service Tag

After replacing a system board, if Easy Restore fails, follow this process to manually enter the Service Tag, using

System

Setup

.

About this task

If you know the system service tag, use the

System Setup

menu to enter the service tag.

Steps

1. Power on the system.
2. To enter the

System Setup

, press

F2

.

3. Click

Service Tag Settings

.

4. Enter the service tag.

NOTE:

You can enter the service tag only when the

Service Tag

field is empty. Ensure that you enter the correct

service tag. Once the service tag is entered, it cannot be updated or changed.

5. Click

OK

.

LOM card and rear I/O board

Removing the LOM card and rear I/O board

Prerequisites

1. Follow the safety guidelines listed in the

Safety instructions

.

2. Follow the procedure listed in the

Before working inside your system

3.

Remove the system board

NOTE:

The procedure to remove the liquid cooling rear I/O board and rear I/O boards is same.

Steps

1. Using a Phillips # 2 screwdriver, remove the screws that secure the LAN on Motherboard (LOM) card and rear I/O board to

the system board.

2. Holding the edges, pull the LOM card or rear I/O board to disconnect from the connector on the system board.

Installing and removing system components

205

«
...
203
204
205
206
207
...
»

Содержание E70S















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для E70S

8649 - Eserver xSeries 225

Бренд: IBM Страницы: 194

EonServ 5000 Series

Бренд: Surveon Страницы: 33

digitalSTROM-Server

Бренд: aizo Страницы: 2

Бренд: Eaton Страницы: 2

xPort Pro XPP1004000-02R

Бренд: Lantronix Страницы: 17

BladeCenter PS703

Бренд: IBM Страницы: 198

AcquiLite EMB A7810

Бренд: Obvius Страницы: 29

Бренд: Infrant Technologies Страницы: 98

Бренд: QNAP Страницы: 69

LaserJet 4200/n

Бренд: HP Страницы: 28

Jetdirect 2700w

Бренд: HP Страницы: 43

Jetdirect 2900nw

Бренд: HP Страницы: 20

LaserJet 4200/n

Бренд: HP Страницы: 36

wp110 - 802.11b Wireless Print Server

Бренд: HP Страницы: 35

JetDirect Ew2500

Бренд: HP Страницы: 2

Бренд: HP Страницы: 18

Бренд: HP Страницы: 25

Jetdirect J7974E

Бренд: HP Страницы: 186

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды