Dell D03T Скачать руководство пользователя страница 11

Страница: 11 / 119

Removing and installing components

NOTE:

The images in this document may differ from your computer depending on the configuration you ordered.

Recommended tools

The procedures in this document may require the following tools:

●

Phillips screwdriver #0

●

Phillips screwdriver #1

●

Torx T20 screwdriver

●

Plastic scribe

Screw list

NOTE:

When removing screws from a component, it is recommended to note the screw type, the quantity of screws, and

then place them in a screw storage box. This is to ensure that the correct number of screws and correct screw type is
restored when the component is replaced.

NOTE:

Some computers have magnetic surfaces. Ensure that the screws are not left attached to such surfaces when

replacing a component.

NOTE:

Screw color may vary with the configuration ordered.

Table 1. Screw list

Component

Screw type

Quantity

Screw image

Front I/O bracket

Captive

Front fan

M3x5

Rear fan

#6-32

Solid-state drive1

M2x3.5

solid-state drive2

M2x3.5

Heat sink

Captive: Torx T20

Hard-drive fan assembly

M3x5

Removing and installing components

Содержание D03T
























































































































Результаты поиска

Содержание D03T

Отзывы:

Похожие инструкции для D03T

Бренды по названию

Популярные бренды

Dell D03T, Руководство по обслуживанию

Результаты поиска

Содержание D03T

Отзывы:

Похожие инструкции для D03T

Бренды по названию

Популярные бренды