Dell Alienware m17 Скачать руководство пользователя | Manualshive

Страница: 51 / 119

background image

Removing the heat sink

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

regulatory_compliance

.

NOTE:

The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to cool before you

touch it.

CAUTION:

For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The oils

in your skin can reduce the heat transfer capability of the thermal grease.

Prerequisites

Remove the

.

Procedure

1. Disconnect the left fan cable from the system board.
2. Disconnect the right fan cable from the system board.
3. Remove the four screws (M2x3) that secure the heat-sink assembly to the palm-rest assembly.
4. In the reverse sequential order (7>6>5>4>3>2>1), loosen the seven captive screws that secure the heat-sink assembly to

the system board.

5. Lift the heat-sink assembly off the system board.

24

Removing the heat sink

51

«
...
49
50
51
52
53
...
»

Содержание Alienware m17
























































































































Отзывы:

Нет отзывов

Похожие инструкции для Alienware m17

Бренд: Razer Страницы: 34

ThinkPad R50 Series

Бренд: IBM Страницы: 2

Toughbook CF-Y5LWEZZBM

Бренд: Panasonic Страницы: 36

Бренд: Atrust Страницы: 2

Бренд: Hamlet Страницы: 2

Apricot AL Series

Бренд: Mitsubishi Electric Страницы: 80

Бренд: NEC Страницы: 28

VersaPro VB VG23T/B-T

Бренд: NEC Страницы: 24

Бренд: NEC Страницы: 24

Бренд: NEC Страницы: 32

Versa TXi Series

Бренд: NEC Страницы: 97

Бренд: NEC Страницы: 100

VERSA S3500 Series

Бренд: NEC Страницы: 110

VERSA P8510 Series

Бренд: NEC Страницы: 94

Бренд: NEC Страницы: 133

VERSA VXI Series

Бренд: NEC Страницы: 106

Бренд: NEC Страницы: 177

Бренд: NEC Страницы: 173

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды