Dell Alienware m17 Скачать руководство пользователя

Страница: 37 / 119

Replacing the wireless card

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/

regulatory_compliance

Procedure

CAUTION:

To avoid damage to the wireless card, do not place any cables under it.

1. Connect the antenna cables to the wireless card.

The following table provides the antenna-cable color scheme for the wireless card supported by your computer.

Table 2. Antenna-cable color scheme

Connectors on the wireless card

Antenna-cable color

Main (white triangle)

White

Auxiliary (black triangle)

Black

2. Slide and replace the wireless-card bracket on the wireless-card.
3. Align the notch on the wireless card with the tab on the wireless-card slot and insert the wireless card at an angle into the

wireless-card slot.

4. Replace the screw (M2x3) that secures the wireless-card bracket to the system board.

Replacing the wireless card

Содержание Alienware m17
























































































































Результаты поиска

Содержание Alienware m17

Отзывы:

Похожие инструкции для Alienware m17

Бренды по названию

Популярные бренды

Dell Alienware m17, Руководство по обслуживанию

Результаты поиска

Содержание Alienware m17

Отзывы:

Похожие инструкции для Alienware m17

Бренды по названию

Популярные бренды