Dell Alienware m17 R2 Скачать руководство пользователя | Manualshive

Страница: 32 / 70

background image

3. Remove the

2230 solid-state drive

. (If applicable)

4. Remove the

2280 solid-state drive

. (If applicable)

5. Remove the

About this task
The following image indicates the location of the keyboard-controller board and provides a visual representation of the removal

procedure.

Steps
1. Remove the two screws (M2x1.9) that secure the keyboard-backlight cable to the keyboard-controller board.
2. Disconnect the keyboard-backlight cable from the keyboard-controller board.
3. Open the latch and disconnect the keyboard-controller board cable from the keyboard-controller board.
4. Open the latch and disconnect the keyboard cable from the keyboard-controller board.
5. Pull on the securing tab to release the keyboard-controls board from the palm-rest assembly.
6. Using the plastic tab, pry and remove the keyboard-controller board from the palm-rest assembly.

Installing the keyboard-controller board

Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.

About this task
The following image indicates the location of the keyboard-controller board and provides a visual representation of the installation

procedure.

32

«
...
30
31
32
33
34
...
»

Содержание Alienware m17 R2







































































Отзывы:

Нет отзывов

Похожие инструкции для Alienware m17 R2

TravelMate 240 series

Бренд: Acer Страницы: 96

Бренд: Navilock Страницы: 2

Бренд: Vivo Страницы: 3

Apricot AL Series

Бренд: Mitsubishi Electric Страницы: 80

Бренд: Toshiba Страницы: 4

PCG-Z1RA Marketing Specifications Sheet

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 1

PCG-VX89 VAIO User Guide (primary manual)

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 1

Бренд: Sony Страницы: 1

PCG-TR2A - VAIO - Pentium M 1 GHz

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 12

Бренд: Sony Страницы: 17

PCG-TR1A - VAIO - Pentium M 900 MHz

Бренд: Sony Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды