Dell Alienware m17 R2 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 70

background image

Installing the M.2 2230 solid-state drive

Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

NOTE: This procedure applies if you are installing a M.2 2230 solid-state drive.

NOTE: Depending on the configuration ordered your computer may have up to two M.2 cards installed. Supported card
configurations per M.2 card slot:

• M.2 2230 solid-state drive + 2230 mounting bracket
• M.2 2280 solid-state drive

NOTE: For PCIe, NVMe solid-state drives a thermal shield is required for optimal heat dissipation and is installed in the
computer when these configurations are ordered. If these configurations are installed After Point-of-Sale (APOS), that is,
after you purchase the computer; contact Dell support to purchase a thermal shield.

NOTE: Before replacing the M.2 card take note that there are two M.2 card slots present on your computer, for:

• the left card slot PCIe, NVMe and SATA AHCI cards are supported.
• the right card slot only PCIe, NVMe cards are supported.

The following image indicates the location of the M.2 2230 solid-state drive and provides a visual representation of the installation

procedure.

15

«
...
13
14
15
16
17
...
»

Содержание Alienware m17 R2







































































Отзывы:

Нет отзывов

Похожие инструкции для Alienware m17 R2

Бренд: Fujitsu Страницы: 116

Бренд: Fujitsu Страницы: 120

Бренд: Fujitsu Страницы: 165

Бренд: Fujitsu Страницы: 122

Бренд: Fujitsu Страницы: 112

Бренд: Fujitsu Страницы: 172

LifeBook E-6555

Бренд: Fujitsu Страницы: 108

Latitude 3390 2-in-1

Бренд: Dell Страницы: 90

MIL-BOOK 1000 Series

Бренд: TAG Страницы: 64

Бренд: Lenovo Страницы: 2

Бренд: Lenovo Страницы: 2

ideapad 730S-13IML

Бренд: Lenovo Страницы: 8

Бренд: Lenovo Страницы: 49

Бренд: Lenovo Страницы: 33

ideapad 320-15IKB

Бренд: Lenovo Страницы: 31

ideapad 730S-13IWL

Бренд: Lenovo Страницы: 43

Бренд: Lenovo Страницы: 87

IdeaPad 5 Pro 14ACN6

Бренд: Lenovo Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды