Dell 13 7000 2-in-1 Скачать руководство пользователя страница 24

Страница: 24 / 95

Removing the heat sink

WARNING: Before working inside your computer, read the safety
information that shipped with your computer and follow the steps in

Before

working inside your computer

. After working inside your computer, follow

the instructions in

After working inside your computer

. For more safety best

practices, see the Regulatory Compliance home page at

www.dell.com/

regulatory_compliance

WARNING: The heat sink may become hot during normal operation. Allow
sufficient time for the heat sink to cool before you touch it.

CAUTION: For maximum cooling of the processor, do not touch the heat
transfer areas on the heat sink. The oils in your skin can reduce the heat
transfer capability of the thermal grease.

Prerequisites

Remove the

base cover

Procedure

In sequential order (indicated on the heat-sink), loosen the four captive screws
that secure the heat sink to the system board.

Содержание 13 7000 2-in-1
































































































Результаты поиска

Содержание 13 7000 2-in-1

Отзывы:

Похожие инструкции для 13 7000 2-in-1

Бренды по названию

Популярные бренды

Dell 13 7000 2-in-1, Руководство по обслуживанию

Результаты поиска

Содержание 13 7000 2-in-1

Отзывы:

Похожие инструкции для 13 7000 2-in-1

Бренды по названию

Популярные бренды