Dell EMC PowerEdge R7525 Скачать руководство пользователя страница 160

Страница: 160 / 209

Installing the OCP card

Prerequisites

1. Follow the safety guidelines listed in the

Safety instructions

on page 46.

2. Follow the procedure listed in the

Before working inside your system

on page 47.

Remove the expansion card riser

Steps

1. If installed, remove the filler bracket.

Figure 121. Removal of filler bracket

2. Open the blue latch on the system board.
3. Slide the OCP card into the slot in the system.
4. Push until the OCP card is connected to the connector on the system board.
5. Close the latch to lock the OCP card to the system.

NOTE:

The numbers on the image do not depict the exact steps. The numbers are for representation of sequence.

160

Installing and removing system components

Содержание PowerEdge R7525


















































































































































































































Результаты поиска

Содержание PowerEdge R7525

Отзывы:

Dell EMC PowerEdge R7525, Инструкция по установке и обслуживанию, Страница: 160 / 209

Результаты поиска

Содержание PowerEdge R7525

Отзывы: