background image

Table 8. Maximum shock specifications 

Maximum shock

Specifications

Operating

One shock pulse in the positive z axis of 31 G for 2.6 ms in the operational
orientation.

Storage

Six consecutively executed shock pulses in the positive and negative x, y,
and z axes (one pulse on each side of the system) of 71 G for up to 2 ms.

Table 9. Maximum altitude specifications 

Maximum altitude

Specifications

Operating

3048 m (10,000 ft)

Storage

12,000 m (39,370 ft)

Table 10. Operating temperature de-rating specifications 

Operating temperature de-rating

Specifications

Up to 35°C (95°F)

Maximum temperature is reduced by 1°C/300 m (1°F/547 ft) above 950 m
(3,117 ft).

35°C to 40°C (95°F to 104°F)

Maximum temperature is reduced by 1°C/175 m (1°F/319 ft) above 950 m
(3,117 ft).

40°C to 45°C (104°F to 113°F)

Maximum temperature is reduced by 1°C/125 m (1°F/228 ft) above 950 m
(3,117 ft).

Expanded operating temperature

Table 11. Expanded operating temperature specifications 

Expanded operating temperature

Specifications

Less than or equal to 10% of annual operating hours

5°C to 40°C at 5% to 85% RH with 29°C dew point.

NOTE:

 Outside the standard operating temperature (10°C to

35°C), the system can operate continuously in temperatures as
low as 5°C and as high as 40°C.

For temperatures between 35°C and 40°C, de-rate maximum allowable dry
bulb temperature by 1°C per 175 m above 950 m (1°F per 319 ft).

Less than or equal to 1% of annual operating hours

–5°C to 45°C at 5% to 90% RH with 29°C dew point.

NOTE:

 Outside the standard operating temperature (10°C to

35°C), the system can operate down to –5°C or up to 45°C for a
maximum of 1% of its annual operating hours.

For temperatures between 40°C and 45°C, de-rate maximum allowable
temperature by 1°C per 125 m above 950 m (1°F per 228 ft).

NOTE:

 When operating in the expanded temperature range, system performance may be impacted.

NOTE:

 When operating in the expanded temperature range, ambient temperature warnings maybe reported on the LCD

panel and in the System Event Log.

34

Technical specifications

Содержание PowerEdge MX5000s












































Отзывы: