Dell EMC ES40 Скачать руководство пользователя страница 61

Страница: 61 / 66

Removing the rails

This procedure describes how to remove the universal rails from a Data Domain or third-party rack.
This procedure assumes the shelf that was installed in the rails has been removed.

About this task

Figure 56 Removing rails

EMC3452

Right rear

Screw (2)

Alignment
pin (2)

Mounting rail

Alignment pins

Adjustable rail

Right front

Mounting rail

Screw (2)

Procedure

1. Remove the two screws from the front channel.

2. Remove the two screws from the rear channel.

3. Push in the alignment pins on the rear channel and remove the rail.

4. Repeat for other rail.

Installing the rails in the cabinet

About this task

Note:

The front edge of each rail is stamped L or R for left or right side, when the rail faces the

cabinet front.

Install each rail in the cabinet.

Procedure

1. From the front of the cabinet, insert the rail alignment pins above and below the bottom U

mark on the rear cabinet channel.

Figure 57 Holes for alignment pins

Alignment pins

here

EMC2892b

Rear channels

2. Pull the sliding rail to the front of the cabinet, and secure it to the front channel at the

middle two holes of the rail using two of the provided screws.

Removing and replacing FRUs

Dell EMC ES40 Expansion Shelf Guide Field Replacement Unit Guide

Содержание ES40



































































Результаты поиска

Содержание ES40

Отзывы:

Похожие инструкции для ES40

Бренды по названию

Популярные бренды

Dell EMC ES40, Руководство по замене модуля

Результаты поиска

Содержание ES40

Отзывы:

Похожие инструкции для ES40

Бренды по названию

Популярные бренды