Dell EMC ES40 Скачать руководство пользователя страница 53

Страница: 53 / 66

Verify the chassis replacement

Procedure

1. Run the

disk rescan

command to discover the disks.

a. If all of the disks are not listed, perform another rescan.

b. If all of the disks are still not listed, check the connection.

2. Enter the

alerts show current

command and confirm that the system has no alerts.

alerts show current

No active alerts.

Note:

If the command output displays hardware failure, use the appropriate sections in

this document (PSU, controller, disk, and fan) to identify and verify the component
connections until there are no alerts.

Bezel Replacement

This section describes how to install or remove a bezel.

Unlocking and removing the front bezel

About this task

NOTICE

You must remove the enclosure’s front bezel to gain access to the disks. The bezel is

required for EMI compliance when the enclosure is powered up. Remove it only to replace or
add a disk.

Procedure

1. Insert the key that shipped with your enclosure into the bezel lock, and turn it to release the

lock.

2. Press the two latch buttons on the bezel surface to release the bezel from the cabinet

(

Figure 46

on page 54).

Removing and replacing FRUs

Dell EMC ES40 Expansion Shelf Guide Field Replacement Unit Guide

Содержание ES40



































































Результаты поиска

Содержание ES40

Отзывы:

Похожие инструкции для ES40

Бренды по названию

Популярные бренды

Dell EMC ES40, Руководство по замене модуля

Результаты поиска

Содержание ES40

Отзывы:

Похожие инструкции для ES40

Бренды по названию

Популярные бренды