Dell EMC ES40 Скачать руководство пользователя страница 36

Страница: 36 / 66

Figure 23 Installing the front bezel

CL4562

Closing the console

About this task

If you opened the console for access to the enclosure with the part you added or replaced, close
the console using the procedure that follows.

Procedure

1. Grasp the free side of the console, and swing the console to the right to close it

2. Gently push on the console until it is closed.

Chassis Replacement

This section describes how to replace a shelf chassis.

Shut down and disconnect the system

Procedure

1. Stop the system using the

system poweroff

command to allow the proper shut down of

the file system and other system components.

Note:

The

system poweroff

command completes when the front panel blue LED

turns off.

For help connecting to a system using a laptop computer and terminal emulator, see the
document

FE Toolkit Inventory and Common Procedures for FRU Tasks

https://

support.emc.com

2. Label each of the cables as to their connection location. Taking a photograph for reference

is also helpful for re-connecting the cables.

3. Disengage the wire clips, then disconnect both AC power cords from the rear of the system.

Removing and replacing FRUs

Dell EMC ES40 Expansion Shelf Guide Field Replacement Unit Guide

Содержание ES40



































































Результаты поиска

Содержание ES40

Отзывы:

Похожие инструкции для ES40

Бренды по названию

Популярные бренды

Dell EMC ES40, Руководство по замене модуля

Результаты поиска

Содержание ES40

Отзывы:

Похожие инструкции для ES40

Бренды по названию

Популярные бренды