Dell EMC ES40 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 66

background image

Complete the procedure

Procedure

1. Return the failed or replaced part(s) to Dell EMC. Reuse the packaging from the new

part(s) and use the included prepaid waybill for shipping. Reference the RMA number on the
outside of the package.

2. Send an autosupport report from the system by entering the

autosupport send

command.

Controller Replacement

This section describes how to replace the controller.

Identify the failed controller

Procedure

1. Check the rear of the shelf for the service LED of the affected controller.

Note:

If the controller needs to be replaced, the service LED is a solid amber.

2. Log in as sysadmin.
3. Enter the

alerts show current

command to display messages indicating controller

failure. A sample output is shown.

#

alerts show current

Id Post Time Severity Class Object Message

---- ---------------------- -------- ------- --------- -----------------

p0-94 Mon Jun 1 9:46:27 2015 WARNING HWFailure Enclosure=9 EVT-MPATH-00006:

Path redundancy is lost.

Enclosure 9 only has

1 active connection path

and the required number is 2.

4. Enter the

enclosure show controllers

command to find the failed controller 9:

#

enclosure show controllers 9

Encl 9

Model ES30

Capacity 15 Slots

WWN N/A

Serial # APM00151918344

Number of Controllers 1

Controller A

WWN 50060481109D607F

Firmware 1.1.0

Serial # JWXCL150700011

Status Not Installed

HOST port 24.0 Gbps

EXP'N port 48.0 Gbps

Status LEDs

Verify the status by checking the LEDs. Controller B is located above Controller A in the center of
the rear panel. The power supply/cooling units are above and below the controllers.

Facing the back panel of the FS15, the Expander ports are the outer of the two ports; the Host
ports are the inner of the two ports. The ports are identified by symbols on the rear panel: a circle
symbol indicates a Host port; a diamond symbol indicates an Expander port.

Removing and replacing FRUs

22

Dell EMC ES40 Expansion Shelf Guide Field Replacement Unit Guide

«
...
20
21
22
23
24
...
»

Содержание ES40



































































Отзывы:

Нет отзывов

Похожие инструкции для ES40

Бренд: ofichairs Страницы: 2

Бренд: LaGrand Страницы: 2

Бренд: WATSON Страницы: 10

Бренд: WATSON Страницы: 17

Бренд: PAIDI Страницы: 31

York RADYORXLGY

Бренд: GPM Страницы: 9

Бренд: Delta Childrens Products Страницы: 19

Бренд: Dancover Страницы: 35

Бренд: Glacier bay Страницы: 4

TY Pennington Style Mayfield 4 PC

Бренд: Sears Страницы: 11

Бренд: Ave Six Страницы: 3

Бренд: Furniture of America Страницы: 13

Basculante PA623P

Бренд: BENITO Страницы: 2

Бренд: feather&black Страницы: 3

Quilter's 7th Heaven 8370

Бренд: Fashion Sewing Cabinets Of America Страницы: 2

Бренд: Accentrics Home Страницы: 9

JULIA ESPINAS OLGA TARRASO BILATERAL

Бренд: Santa & Cole Urbidermis Страницы: 11

Бренд: Walker Edison Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды