Project __________________________________
Item ____________________________________
Quantity ________________________________
CSI Section 11400
Approved _______________________________
Date ____________________________________
980 S. Isabella Rd.
Mt. Pleasant, Michigan 48858
Phone: 800-733-8948 or 989-773-7981
Fax: 800-669-0619
www.delfield.com
Exterior top
is one-piece 22-gauge stainless steel with integral
2.12” (5.4cm) square nosing at the front. The backsplash is full
width and 4” (10cm) tall. Top of drawer unit has openings
to accept eight 1/6-size 4” (10cm) deep plastic pans. Top of
door unit has openings to accept eight 1/6-size 4” or 6” (10cm
or 15cm) deep plastic pans. Adapter bars and 1/6 pans are
supplied by Delfield. Temperature in top opening to maintain
33°F (1°C) to 41°F (5°C), with pans recessed 2.5” (6.4cm) at 86°F
ambient room temperature, meeting NSF 7 requirements. One
60” x 10” x .5” (152cm x 25.4cm x 1.3cm) polyethylene cutting
board treated with antimicrobial agent is mounted on the top
at the front edge.
Dual level pan brackets
allow the pans to be lowered an
additional inch in the unit without tools to provide additional
pan temperature holding performance.
Exterior back and bottom
are two-piece 24-gauge galvanized
steel. Exterior ends are stainless steel.
Interior sides
are thermoformed ABS plastic with shelf
supports. Base is fully insulated with high-density foamed in
place environmentally friendly, Kyoto Protocol Compliant, Non
ODP (Ozone Depletion Potential), Non GWP (Global Warming
Potential) polyurethane.
Refrigeration system
uses HFC-404A refrigerant. Compressor
is 1/2 H.P., with condenser coil and condensate evaporator
mounted on rear of the cabinet. Evaporator coils are located
on the interior rear wall of the cabinet. Refrigerant flow is
controlled by a capillary tube. Cabinet maintains an interior
cabinet temperature of 36°F to 40°F (2°C to 4°C).
ACT control:
ACT electronic, solid state control, mounted on
the exterior rear of the cabinet, allows unit to maintain precise
temperatures in heavy duty conditions.
Electrical connections
are 115 volt, 60 Hertz, single phase.
Unit has a 6’ (1.8m) long electrical cord and NEMA 5-15P plug.
Casters:
Equipment is mounted on 5” (13cm) diameter plate
casters with front two locking. Equipment clearance above the
floor is 2.5” (6cm).
The following applies to two door models only.
Doors have
a 24-gauge stainless steel exterior, with thermoformed ABS
plastic interior liner. Cabinet has one adjustable epoxy-coated
wire shelf per door opening.
The following applies to four drawer models only.
Drawer fronts have a 24-gauge stainless steel exterior, with
thermoformed ABS plastic interior liner. Drawer frames are
12-gauge stainless steel. Drawer slides are 11-gauge stainless
steel with Delrin bearings. Each section has two drawers. Each
top drawer holds one full size 12” x 20” (30.5cm x 50.8cm)
pan, three 1/9 size and three 1/6 size 4”-6” (10.2cm -15.2cm)
deep pans. Each bottom drawer holds one 12” x 20” (30.5cm x
50.8cm) pan, three 1/9 size and three 1/6 size 4” (10.2cm) deep
pans. Pans supplied by others.
Specifications
Standard Features
Options &
Accessories
•
Patented air screen ensures product stays cold
without drying it out
•
All 4400 Series units are 100% front breathing,
which allows the unit to be pushed against
a wall or built into a cabinet or an existing
line up
•
Durable, rugged stainless steel sides, top and
front
•
Features Delfield’s exclusive ABS interior (on
sides). ABS is extremely durable - it won’t dent,
chip or corrode and is backed by a limited
lifetime warranty
•
Delfield supplies 1/6 size pans and positive
placement adapter bars for top opening
•
Dual level pan brackets allow the pans to be
lowered an additional inch in the unit without
tools to provide additional pan temperature
holding performance
•
Salad top refrigerators are standard with 10”
wide, dishwasher safe polyethylene cutting
board treated with antimicrobial agent
•
“D” prefix models feature Delfield’s new drawer
system. Drawers are backed by a 10-year
warranty on the track assembly
•
Environmentally friendly R404A refrigerant
•
High density foamed in place environmentally
friendly, Kyoto Protocol Compliant, Non ODP
(Ozone Depletion Potential), Non GWP (Global
•
ST4460N-8
Two section with doors, eight pan capacity
•
STD4460N-8
Two section with drawers, eight pan capacity
Models
ST4460 Salad Top
Front-Breathing Self-Contained Salad Top Refrigerated
Bases
ST4460 Salad
Top: F
ront
-Br
eathing S
elf-
Contained Salad
Top R
efr
igerat
ed Bases
Warming Potential) polyurethane
keeps energy costs low
•
Black recessed quick grip handle
•
Standard on 5” casters for easy
cleaning and installation
•
6’ cord and plug supplied
•
One epoxy coated wire shelf standard,
installed per door section
•
ACT solid state electronic control
•
"ST" models have a 4" stainless steel
backsplash
•
One year parts and 90 day labor
standard warranty
•
Flat lift off cover
•
18” wide single tier overshelf
•
Stainless steel finish on back
•
Plastic laminate on front
•
Additional wire shelves
•
3” casters, 3.75” ride height
•
Door lock (solid door models only)
•
Exterior thermometer (solid door
models only)
•
Glass door(s)
•
220V/50 Hertz electrical system*
* Inclusion of this option will alter
electrical specifications of the unit
STD4460N-8
