PROJECT
ITEM #
QUANTITY
DATE
APPROVAL
The Delfield Company, 980 S. Isabella Rd., Mt. Pleasant, MI 48858, U.S.A. • (800) 733-8821 • Fax (800) 669-0619 • www.delfield.com
Delfield reserves the right to make changes in design or specifications without prior notice. ©2002 The Delfield Company. All rights reserved. Printed in U.S.A.
CAB3
Mobile enclosed three-stack dish dispensers
Short form specifications
Cabinet top shall be 16-gauge stainless steel with all corners welded and polished and
reinforced with heavy-gauge channels. Cabinet exterior panels and corner support angles
shall be 20-gauge stainless steel. Unit shall have four 4.00" (10.2cm) diameter polyolefin
swivel casters (all locking), and non-marking gray bumpers at each corner.
Dispenser tube shall have 3 vertical side channels and a bottom brace of 22-gauge
stainless steel. Top supporting flange shall be 18-gauge stainless steel . Flange, channels
and bottom brace shall be integrally welded together. Flange shall have 3 guide posts molded
from high impact plastic.
Self-leveling mechanisms shall be field adjustable by adding or removing stainless steel
extension springs on perimeter of vertical side channels. The dish carrier head shall be
stainless steel welded rods with a removable 18-gauge stainless steel top plate.
Capacity of tubes shall be approximately 72 dishes, with a maximum stacking height of
24.00" (61.0cm).
NOTE:
Models without “-ET” or “-QT” suffix are unheated.
THE FOLLOWING APPLIES TO CAB3-ET EVEN TEMP HEATED DISPENSERS ONLY:
Unit shall be supplied with 9' (2.7m) cord and NEMA 5-20P plug. Electrical connections
shall be 120 volt, 60 hertz, single phase.
Each tube shall have its own convection heating module consisting of a single 400 watt
heating element and fan motor, located in the center of the interior bottom cavity. Air intake
shall have a filter. Each tube shall have an adjustable thermostat inside the motor housing
and an ON/OFF switch on one of the dish guide posts. Unit shall maintain temperature
between 120°F–140°F (49°C–60°C).
THE FOLLOWING APPLIES TO CAB3-QT QUICK TEMP HEATED DISPENSERS ONLY:
Unit shall be supplied with 9' (2.7m) cord and NEMA 6-20P plug. Electrical connections
shall be 208-230 volt, 60 hertz, single phase.
Each tube shall have its own convection heating module consisting of a single 700 watt
heating element and fan motor, located in the center of the interior bottom cavity. Air intake
shall have a filter. Each tube shall have an adjustable thermostat inside the motor housing
and an ON/OFF switch on one of the dish guide posts. Unit shall maintain temperature
between 150°F–170°F (66°C–77°C).
Each tube shall have a stainless steel cover.
Optional accessories & modifications
• Heavy-duty casters (consult factory)
• Flange-mount feet in lieu of casters
• Special dispenser tube heights
• 12" (30.5cm) dia. stainless steel dish dispenser tray (CAB3-1200, CAB3-1200-ET and
CAB3-1200-QT only)
• Non-marring adjustment rods for oval dishes and various dish diameters (–813
through –1450 sizes only)
• Stainless steel cover with access to dishes (–813 through –1450 sizes only; stan-
dard on QT models)
• Stainless steel tube cover
• Hold-down rod for dispenser tubes
• Wrap-around bumpers (adds 1.75" [4.4cm] to overall length and depth)
• Fiberglas
®
panels
• Laminate panels
• Special voltages (consult factory)
Model CAB3-575
with optional wrap-around bumpers