DELAIR UX11 Скачать руководство пользователя страница 53

Страница: 53 / 94

User Manual UX11

8.3 Assembling the UX11 aircraft

CAUTION

When handling the fuselage, do not hold it by motor housing (orange plastic part covering the motor).

Take the wings, the fuselage, the connecting rod and the supporting foam plate out of the

transport bag.

Place the supporting foam plate on the transport bag.

Place the fuselage on top of the supporting foam plate (with the Pitot tube location facing up).

Take a Pitot tube out of the transport bag.

Blow in the static pressure port hole and in the dynamic total pressure port hole to make sure

they are not clogged.

Attach the Pitot tube on the double barbs on top of the fuselage.

Place the connecting rod in the fuselage and center it.

Delair

676, Rue Max Planck – 31670 Toulouse-Labège, France

Tel: +33 (0) 5 82 95 44 06

| www.delair.aero

Capital: 238 110,30 € - APE: 3030Z – Intra-Community VAT number: FR90 53 09 69 781 – 530 969 781 R.C.S. Toulouse

This document is the sole property of Delair and cannot be used or reproduced without the written authorization of Delair.

Содержание UX11































































































Результаты поиска

Содержание UX11

Отзывы:

DELAIR UX11, Руководство пользователя, Страница: 53 / 94

Результаты поиска

Содержание UX11

Отзывы: