DELAIR UX11 Скачать руководство пользователя страница 42

Страница: 42 / 94

User Manual UX11

5.5 Viewing the flight plan elevation

To ensure that the aircraft stays within its safe capabilities, tap

SHOW ELEVATION

to view the elevation

profile.
A graph is displayed that shows the ground elevation, flight height and, if set, the geofence height.
The

SHOW ELEVATION

button turns red when there are issues with the flight height. For example

when the flight is set too low or if the slope of the ground is steeper than the rate of climb of the

aircraft.
When the

SHOW ELEVATION

button is red the user must Tap on it to analyse the reason for the

warning. The following elevation graph is shown:

In case of long flight plans (requiring more than one flight), it is possible to check the elevation profile

of the subsequent flights (after the current flight) by tapping the FULL FLIGHT PLAN tab. This allows

you to anticipate issues that may appears on subsequent flights when resuming flight plan.

Delair

676, Rue Max Planck – 31670 Toulouse-Labège, France

Tel: +33 (0) 5 82 95 44 06

| www.delair.aero

Capital: 238 110,30 € - APE: 3030Z – Intra-Community VAT number: FR90 53 09 69 781 – 530 969 781 R.C.S. Toulouse

This document is the sole property of Delair and cannot be used or reproduced without the written authorization of Delair.

Содержание UX11































































































Результаты поиска

Содержание UX11

Отзывы:

DELAIR UX11, Руководство пользователя, Страница: 42 / 94

Результаты поиска

Содержание UX11

Отзывы: