DELAIR UX11 Скачать руководство пользователя страница 20

Страница: 20 / 94

User Manual UX11

Up to 6 propellers (5)

Up to 4 batteries (6)

One Torx T10 screwdriver (7)

One spare belly plate (8)

Three Pitot tubes (9)

One charger (10)

Delair Link (11)

Lens cleaning kit, cables and adapters (in different pockets)

Supporting foam plate (wing spacer foam) (12)

One tablet also fits in outside pocket.

2.4.3

Aircraft docking

The wing spacer foam also functions as a supporting foam plate for docking the aircraft during

assembling, pre-flight operations and disassembling.
The figure below shows the wing spacer foam placed on the transport bag.

Delair

676, Rue Max Planck – 31670 Toulouse-Labège, France

Tel: +33 (0) 5 82 95 44 06

| www.delair.aero

Capital: 238 110,30 € - APE: 3030Z – Intra-Community VAT number: FR90 53 09 69 781 – 530 969 781 R.C.S. Toulouse

This document is the sole property of Delair and cannot be used or reproduced without the written authorization of Delair.

Содержание UX11































































































Результаты поиска

Содержание UX11

Отзывы:

DELAIR UX11, Руководство пользователя, Страница: 20 / 94

Результаты поиска

Содержание UX11

Отзывы: