background image

Diagnostics: Dell PowerVault 124T DLT VS160 Autoloader User's Guide

file:///T|/htdocs/stor-sys/124T/en/124tvs16/diag.html[12/5/2012 10:26:06 AM]

3.  Press 

Enter

 to return to the 

Diagnostics

 submenu. Refer to the Remote Management Unit for any test results.

To stop a test from the Remote Management Unit:

1.  Select the

 Stop Test

 button in the 

Diagnostics

 test section of the Error Logs and Diagnostics page.

2.  Select 

View Status

 to see the results of the command. 

Test Stopped

 displays along with any test results.

Front Panel Diagnostic Tests

You can perform the following diagnostic tests using the front panel:

Picker Test

Magazine Test

Inventory Test

Random Moves

To perform any of the front panel diagnostic tests:

1.  From any menu, click the 

Diagnostics

 heading. The 

Diagnostics

 screen displays.

2.  Scroll to the test you want to run and press 

Enter

.

If you are already logged in as Administrator, the test begins executing immediately. The message 

Running Test

appears while the test is running.

NOTE:

 Each test takes from 30 seconds to several minutes to complete. To stop the test prematurely, see

"

Stopping a Diagnostic Test

."

3.  If you are not logged in, you will be asked to enter the Administrator password. Do the following:

From the front panel, enter the administrator password by using the 

Up

 and 

Down

 scroll arrows to select each

digit, and then press 

Enter

 to move to the next digit. To move to the previous digit, press 

Escape

. When you

have entered the entire six digit password, you will be asked to press 

Enter

 one more time to submit the

password. If the password is incorrect, you will be asked to re-enter it using the same procedure. Otherwise, you

will be returned to the 

Diagnostics

 menu. Press 

Enter

 to run the desired test.

Running Test

 appears while the test is in progress. To stop the test prematurely, see "

Stopping a Diagnostic

Test

."

4.  If the test is successful, press 

Enter

 to return to the 

Diagnostic

 test menu. For detailed results of a test, use the

Remote Management Unit to retrieve the diagnostic test status (see "

Running Diagnostic Tests

").

Remote Management Unit Diagnostic Tests

Because some of the diagnostic tests require you to insert a minimum of two cartridges into the autoloader, you cannot

perform these tests from a remote location. You can perform the following diagnostic tests from the Remote Management

Unit:

Loader - Picker Test

Loader - Magazine Test

Loader - Inventory Test

Random Moves

NOTE:

 The Remote Management Unit allows you to request all diagnostic tests, but any tests that require a

Содержание PowerVault 124T DLT VS160
















































































Отзывы: