background image

29 

30SD, 36SD, 45SD 

 

Rev. Nov2014 

Troubleshooting 

Problem Possible 

Causes 

Solution 

Engine will not start 

1.  Key in the OFF position 
2.  Insufficient fuel in the tank 
3.  Air bubble in the fuel line 
4.  Fuel valve in OFF position 
5.  Choke not ON 
6.  Choke linkage out of adjustment 
7.  Loose spark plug wire  
8.  Fouled spark plug  
9.  Plugged or dirty air filter  
10.  Bad / old gasoline 
 

1.  Turn key to ON position 
2. Add 

gasoline 

3.  Prime engine or shake bubble out 
4.  Turn valve ON 
5. Turn 

choke 

ON 

6.  Refer to Engine Owner’s Manual 
7. Add 

engine 

oil 

8.  Tighten wire or connections 
9.  Clean or replace the plug 
10.  Clean or replace the air filter 
11.  Drain and replace with fresh gasoline 

 
 

Engine will not keep 
running/quits 

1.  Water in the fuel 
2.  Fuel valve is OFF 
3.  Low engine oil 

 

1.  Drain and replace with fresh fuel 
2.  Turn fuel valve ON 
3. Add 

engine 

oil 

Augers do not turn 

1.  Shear pins holding the augers may 

have sheared. 

2.  If the pins sheared, replace them as needed after  

applying lubricant into the shaft. Call GXi Parts & 
Service at 1-919-550-3259 or email: 
[email protected] for parts. 

Shaft is not turning 

1.  Shear-Pins holding the augers may 

have sheared. 

2.  Check the gearbox. 

If the pins sheared, replace them as needed after  
applying lubricant into the shaft.  

Call GXi Parts & Service at 1-919-550-3259or email: 
[email protected] for parts. 

Snow blower always pulls 
to one side 

1.  Skid shoes and / or scrapper blade 

dragging more on one side than the 
other 

2.  Air pressure in tires is not equal on 

both sides. 

 

1.  Adjust skid shoes and / or scrapper blade so the 

scrapper blade drags uniformly on the surface 
being blown. 

2.  Check air in tires.  Add or remove pressure as 

needed. 

 

Engine will not start with 
electric starter 

1.  Not using proper gauge cord 
2.  Safety key is loose 
3.  No power from electrical source 
 

1.  Use 120V 16 gauge cord in good condition. 
2.  Verify the safety key is fully inserted. 
3.  Check breaker and plug connections 

Fuel is leaking from the 
engine. 

1.  Primer bulb was pressed too many 

times. 

 
2.  Fuel hose has become dis-connected 
3.  Carburetor has contaminants in it 

causing the bowl to flood. 

 

1.  Do not press primer more than 3 times. Wipe off 

excess fuel and allow to dry COMPLETELY before 
attempting to start 

2.  Re-connect fuel hose and clamp(s) 
3.  Fuel tank and carburetor needs to be flushed and 

carburetor needs cleaning. 

Содержание 30SD










































Отзывы: