manualshive.com logo in svg

Deif SGC 120, Руководство пользователя

Поделиться
Скачать
Deif SGC 120 Скачать руководство пользователя страница 25

Level 2

Range

Always

Activation Delay
(ACTIVATION DELAY)

0 to 60 s 

6.2.4 Analogue inputs

Table 6.7

Analogue Input 1 (ENG TEMP / DIG G)

Level 2

Range

Use Input As
(SENSOR SELECTION)

Not used
Digital Input G
Anlg In Eng Temp

(Digital) Source
((DIG) SOURCE)

See 

Digital input source selection

 in this document

Name
(NAME)

Auxiliary Input G 

(Digital) Polarity
((DIG) POLARITY)

Close to Activate
Open to Activate

(Digital) Action
((DIG) ACTION)

None
Notification
Warning
Electrical Trip
Shutdown

(Digital) Activation
((DIG) ACTIVATION)

Never
From Engine Start
From Monitoring On
Always

(Digital) Activation Delay
((DIG) ACTIVATION DELAY)

1 to 60 s 

(ETS) Circuit Fault Action
(OPEN CKT ALARM)

None
Notification
Warning
Electrical Trip
Shutdown

(ETS) Engine Temperature Sensor Calibration Table

Resistance: 0 to 1000 Ω
Temperature: 25 to 300 °C

Table 6.8

Analogue Input 2 (FUEL LVL / DIG H)

Level 2

Range

Use Input As
(SENSOR SELECTION)

Not used
Digital Input H
Fuel Level Sensor

(Digital) Source
((DIG) SOURCE)

See 

Digital input source selection

 in this document

Name
(NAME)

Auxiliary Input H 

(Digital) Polarity
((DIG) POLARITY)

Close to Activate
Open to Activate

(Digital) Action

None

USER MANUAL 4189341226A UK 

Page 25 of 72

Содержание SGC 120









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды