Deif IMD 100 Скачать руководство пользователя страница 122

Страница: 122 / 243

IMD 100 Integration manual 4189360015 Rev. G

IMD configuration

www.deif.com/wind-power

Page 122 of 243

8.7.3 Configuring the charger manually

The charger has 2 parameter types:

•

Basic parameters

: Must always be configured.

•

Parameter configuration

: Can either be configured manually or used with the factory defaults

(select with the “Set factory default” button). There is a set of factory defaults parameters for each
SE type.

NOTE

To achieve maximum performance and life time of the energy source, consult the energy

source supplier, and have the applicable charging characteristics at hand.

8.7.3.1 Configuring type and basic configuration

Click on the “SE charger” tab. If the Setup mode is disabled (

) click on the

“Disabled” button to enable the Setup mode.

Содержание IMD 100




















































































































































































































































Результаты поиска

Содержание IMD 100

Отзывы:

Похожие инструкции для IMD 100

Бренды по названию

Популярные бренды

Deif IMD 100, Руководство по интеграции

Результаты поиска

Содержание IMD 100

Отзывы:

Похожие инструкции для IMD 100

Бренды по названию

Популярные бренды