Deif IMD 100 Скачать руководство пользователя страница 110

Страница: 110 / 243

IMD 100 Integration manual 4189360015 Rev. G

IMD configuration

www.deif.com/wind-power

Page 110 of 243

8.5.3 Configuring current parameters

Fill in the following fields:

•

PID (

proportional

–integral–derivative)

control parameters

: Only experienced and qualified

person should adjust this parameter (see also section

8.5.1

on page

103

Kp:

Proportional amplification in the current controller.

Ti:

Integration time for the current controller.

TiM:

Maximum value of the current integral memory.

xKp2:

Proportional amplification on overshoot current controller.

Kf:

Feedforward amplification current controller.

•

Application current definitions

Ramp time:

The time in us that the motor will accelerate from zero to I con eff.

Содержание IMD 100




















































































































































































































































Результаты поиска

Содержание IMD 100

Отзывы:

Похожие инструкции для IMD 100

Бренды по названию

Популярные бренды

Deif IMD 100, Руководство по интеграции

Результаты поиска

Содержание IMD 100

Отзывы:

Похожие инструкции для IMD 100

Бренды по названию

Популярные бренды