Deger DEGERtracker D100 Скачать руководство пользователя | Manualshive

Страница: 26 / 44

background image

24.03.2017

ASSEMBLY AND OPERATING MANUAL DEGERtracker D60H, D80, D100

Page 26

6.7.1

Clamping between modules

Assembly

1.

preassembled fastening slide into the slot

2.

positioning

3.

place the module flush to the bolts

4.

tighten the bolt M6

ATTENTION!
The permissible fastening and the area of fastening of the modules must be comply with the module
manufacturer specification.
Permitted maximum value for this bolt is 8Nm.

DEGERenergie doesn’t assume any responsibility for this value.

Optional: WEEB-DPR for bonding and grounding

Please contact DEGERenergie for further information

6.7.2

Clamping at end of module surface

ATTENTION!
The permissible fastening and the area of fastening of the modules must be comply with the module
manufacturer specification.
Permitted maximum value for this bolt is 20Nm.

DEGERenergie do

esn’t assume any responsibility for this value.

bolt

M6

middle plate round

or.

Centre plate HD

sliding nut M6

bolt M8

end clamp

sliding nut M8

«
...
24
25
26
27
28
...
»

Содержание DEGERtracker D100













































Отзывы:

Нет отзывов

Похожие инструкции для DEGERtracker D100

7-10-30LP8 UP-KIT

Бренд: M2 Antenna Systems Страницы: 6

Бренд: weBoost Страницы: 28

Бренд: H3C Страницы: 6

Бренд: UltraPro Страницы: 2

Бренд: NETGEAR Страницы: 12

ProSafe ANT224D10

Бренд: NETGEAR Страницы: 2

VISION SCIBORG TR365D

Бренд: Kiramek Страницы: 12

Бренд: AOR Страницы: 16

Бренд: RCA Страницы: 8

Бренд: RCA Страницы: 12

Бренд: Greyline Страницы: 4

Бренд: Hughes Страницы: 62

Бренд: Ercogener Страницы: 35

Бренд: Abel & Profit Страницы: 3

Бренд: TracVision Страницы: 50

Бренд: Monoprice Страницы: 2

Бренд: Panorama Antennas Страницы: 2

NL-6022MP u-blox NEO-6P

Бренд: Navilock Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды