DeDietrich IX 145-110 Скачать руководство пользователя страница 94

Страница: 94 / 132

Pre-setting selected

Hours programmed

Time setting 1

6:00 to 23:00

Time setting 2

06:00...08:00 – 17:00...23:00

Time setting 3

06:00...08:00 – 11:00...13:00 – 17:00...23:00

For more information, see

Changing the operating mode, page 88

Default time ranges

Tab.74 Time ranges according to the groups of days selected
Program line 514 (heating), 574 (domestic hot water)

Groups of days

Pre-set programs

On 1 - Off 1

On 2 - Off 2

On 3 - Off 3

Mon-Sun

06:00 - 08:00

11:00 - 13:00

17:00 - 23:00

Mon-Fri

06:00 - 08:00

17:00 - 23:00

Sat-Sun

06:00 - 23:00

Tab.75 Time ranges according to the days selected
Program line 501, 502, 503, 504, 505, 506 (heating) - 561, 562, 563, 564, 565, 566 (domestic hot water)

Single days

Pre-set programs

On 1 - Off 1

On 2 - Off 2

On 3 - Off 3

Monday-Tuesday-Wed

nesday-Thursday-Friday-

Saturday-Sunday

06:00 - 08:00

11:00 - 13:00

17:00 - 23:00

For more information, see

Changing the operating mode, page 88

Selecting a Timer Program

1. Select a heating circuit.
2. Press the

key to access the parameters.

3. Select the Time central heating CH1 menu by turning the

button.

Important

For heating circuits 2 and 3, select the parameters Time central

heating CH2

or Time setting 3/CHP.

For the domestic hot water circuit, select the parameter Time

hot water.

4. Confirm the menu selection by pressing the button.

The parameter Select days (500, 520, 540 or 560) appears.

Fig.94

MW-3000071-EN-03

MENU

----------------------------------------------------

Information

Set time and date

10 Settings

7702703 - v04 - 05092019

Содержание IX 145-110





































































































































Результаты поиска

Содержание IX 145-110

Отзывы:

Бренды по названию

Популярные бренды

DeDietrich IX 145-110, Инструкция по установке и обслуживанию

Результаты поиска

Содержание IX 145-110

Отзывы:

Бренды по названию

Популярные бренды