Quick Start Guide
MI-Q-TVE/E2-0
Installing the Hard Drive
The hard drive for the unit is provided un-installed.
1) Unlock the keylock on the front of the TransVu Express and withdraw
the caddy.
2) Remove from the protective packaging from the Hard drive and insert
into the caddy. Ensure the pins on the hard drive are pointing away
from the front of the caddy drawer and the label on the hard drive
is facing upwards and visible when the hard drive is placed in the
caddy.
3) Carefully slide the caddy back into the TransVu Express. Remember
to lock the caddy into the TransVu Express using the keylock. Failure
to do so will prevent the unit starting up.
Connections
Please ensure the following are available and have been tested prior to the
installation:
• 10 ~ 30VDC Vehicle Power Source
• Crossed network cable required for web page setup
• Active video signals.
• Correctly terminated cable loom, please see TransVu Express
installation manual for further information.
• Desk or Laptop PC with CD ROM drive with Internet Explorer 5.5
upwards for unit configuration
• Note that pin 35 of the connector provides a switched output of the
input voltage NOT a 12V regulated supply
WARNING: Operate the TransVu Express from the power source
indicated on the label. Failure to do so may cause injury, and
will invalidate the warranty. Under no circumstances make
connections to this unit whilst power is applied.
37 way Connector Layout
Numbers looking at the front of the male connector.
1
19
37
20
Read the Instructions First
Read all safety and operating instructions and labels before working with the
TransVu Express. This Quick Start Guide is not for use in isolation and should
always be used in conjunction with the main user manuals.
Please contact the supplier with any problems. Report any difficulties with this
guide to Dedicated Micros at the UK office. Addresses and phone numbers
are given in the user guides and also in the Contacts area of the website at:
http://www.dedicatedmicros.com
Servicing
Do not attempt to service this unit. Opening or removing covers may expose
dangerous voltages or other hazards. Refer all servicing to qualified service
personnel.
Lifting and Handling
Always follow health and safety guidelines when lifting the unit from the box
or installing the TransVu Express unit.
Unpacking
Remove all the items from the box and check components listed below are
included.
The TransVu Express package contains the following items:
• TransVu Express unit
• Mounting Plate
• Rubber Shock Mounts
• Installation CD ROM
• Installation Guide
• Configuration & Operation Guide
• Setup Guide
• Quick Start Guide (this document)
If any of these items are missing, please contact the distributer Customer
Services department.
Location
• Drilling extra holes in the casing of the unit will immediately invalidate
the warranty.
• The unit should be mounted away from any possible places where
water may puddle during vehicle operation as the TransVu Express
casing is not rated for submersion.
The unit should be mounted on a secure base free from resonance and
secondary vibrations using the mounting plate provided.
• A fitment area of 290mm x 190mm x 90mm (11½” x 7½” x 3½” ) is
required.
• Extra space is required around to the plug area to ensure easy
removal.
• Refer to TransVu Express Installation and Configuration & Operation
Guides for more information.
Pin
Description
1 Monitor Output (1V p-p CVBS video)
2 Video ground
3 Camera 8 (1V p-p CVBS video)
4 Camera 5 (1V p-p CVBS video)
5 Video ground
6 Camera 4 (1V p-p CVBS video)
7 Camera 1 (1V p-p CVBS video)
8 Audio ground
9 Audio Input 2 (mic-level)
10 Relay output (negative side)
11 COM3 port: RS-232 TXD
12 10/100 Ethernet port: TX+
13 10/100 Ethernet port: TX-
14 Alarm Input 1
15 Alarm Input 3
16 Switched power output – negative
17 Power input - negative: ground
18 Power input - negative: ground
19 Video ground
Pin
Description
20 Camera 7 (1V p-p CVBS video)
21 Camera 6 (1V p-p CVBS video)
22 Video ground
23 Camera 3 (1V p-p CVBS video)
24 Camera 2 (1V p-p CVBS video)
25 Video ground
26 Audio Input 1 (line-level)
27 Relay output (positive side)
28 Alarm ground
29 Alarm Input 2
30 Ignition sense input
31 COM3 port: RS-232 RXD
32 COM3 ground
33 10/100 Ethernet port: RX+
34 10/100 Ethernet port: RX-
35 Switched power output – positive (1A)
36 Power input - positive: 10V – 30V DC
37 Power input - positive: 10V – 30V DC
15 way Expansion Port Layout
Numbers looking at the front of the male connector.
1
6
5
10
15
11
PIN NO. FUNCTION
1
POWER MANGER RS232-RXD
2
POWER MANGER RS232-TXD
3
GND
4
COM1 RS232-RXD
5
COM1 RS232-TXD
6
COM2 - RS485+/R
7
COM2 - RS485-/RS422_TX-
8
GND
9
COM1 CTS
10
COM1 RTS
11
COM2 - R
12
COM2 - RS422_RX-
13
GND
14
AUDIO OUT 0 line level
15
AUDIO OUT 1 line level
