Dectris PILATUS 3 R 100K-M Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 39

Dectris PILATUS 3 R 100K-M Скачать руководство пользователя страница 13

3.4. Vacuum Conditions for Detectors with Optional Vacuum Compatibility

DECTRIS

®

detectors can be provided for vacuum operation. The typical reachable vacuum is 10

−3

mbar (read-out elec-

tronics in vacuum) or 10

-6

mbar (only detector head in vacuum). The out-gassing rate and content are not specified. The

vacuum compatibility option guarantees that the detector will operate in the mentioned vacuum range. Detectors ordered
with a vacuum compatibility option have been tested in vacuum.

To see if a detector is vacuum compatible, check the conditions mentioned in section 2.1

Warning

#3

Only systems with a vacuum compatibility option are allowed to be operated in vacuum. Please contact
[email protected] for information regarding vacuum compatibility upgrade.

For in-vacuum operation of the detector following conditions must be fulfilled:

Table 3.8:

In-Vacuum Operating Conditions

In-Vacuum Condition

Definition

Pressure during operation

atmospheric pressure or less than 0.01 mbar

1 bar

10

-

² mbar

1 Pa

10⁵ Pa

...

Detector mounting plate temperature during
operation

+10

◦

C to 25

◦

C

Thermal stabilization unit set temperature in vacuum

10

◦

C

Chamber temperature during ”bake-out” (detector
unpowered)

max. +60

◦

C (for temperatures > 40

◦

C make sure the thermal

stabilization unit is set to +40

◦

C and running)

PILATUS3 R 100K-M Technical Specifications v1.2.2

8 | 34

«
...
11
12
13
14
15
...
»

Содержание PILATUS 3 R 100K-M








































Отзывы:

Нет отзывов