manualshive.com logo in svg

DCS CAD-36, Инструкция по установке/Руководство пользователя

Поделиться
Скачать
DCS CAD-36 Скачать руководство пользователя страница 18

18

INSTALLATION

Side shelf assembly instructions (optional)

Optional attach side shelf accessory on either side

Note: side shelf model CAD1-SK can be installed with the head already on the cart.

Screw two shoulder bolts into the bottom 
threaded holes on the side of the cart. 
Tighten with 5/32 Allen Key.

Slide shelf brackets over the shoulder bolts 
and install top screw, attaching the side-shelf 
brackets onto the cart. Tighten with Phillips 
screwdriver. 

Holding the side shelf, install two shoulder 
bolts into the slot and screw into the side 
shelf tray. Tighten with a 3/16 Allen key.

Place shelf in the up position and check for 
level. If shelf is not level, adjust side shelf set 
screw. Set screws can be adjusted using a 
3/32 Allen Key. Turn the Allen key clockwise 
to raise the shelf. Turn 1/4 turn and review 
to see if the shelf is level. The set screws in 
the left and right bracket should be adjusted 
equally to ensure the shelf sits level.

Optional wood cutting board (model # CAD1-WCB, 
70861) can be purchased as an accessory from 
www.fisherpaykel.com

2

3

4

1

Shoulder bolt 

screw location

Содержание CAD-36
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды