SERVICE CALLS TO RECTIFY FAULTS CAUSED BY `THE LACK OF ROUTINE MAINTENANCE` WILL BE CHARGED FOR AND YOUR WARRANTY MAY BE AFFECTED
www.directcatering.co.uk
OPERATING AND MAINTENANCE INSTRUCTIONS
SXD45A IS D / SXD50A IS D
FOOT VALVES FOR
CHEMICAL
CONTAINER TUBES
DRAIN PLUG
FILTER
BOWL
OUTLET HOLE
RINSE ARM NUT
RINSE JETS
WASH JETS
RINSE PIN
RINSE ARM
WASH
POWER
SWITCH
CYCLE START
SWITCH
MACHINE
READY
LAMP
(OPTIONAL)
DRAIN PUMP
REMOVE DRAIN
PLUG AND SWITCH
THE MACHINE OFF
TO START THE
AUTOMATIC DRAIN
PUMP CYCLE
CYCLE TIME
SWITCH
2 MINUTE ~ 3MINUTE
CYCLE
SELECTION
LAMP
CYCLE LAMP
POWER LAMP
WATER SOFTENER
START SWITCH
WATER SOFTENER
REGENERATION
LAMP
SALT LOW
LAMP
OPERATION
•
REMOVE ALL DEBRIS FROM THE ITEMS TO BE WASHED, BEFORE PLACING THEM INTO THE BASKET.
•
CLOSE THE DOOR, PRESS THE
CYCLE START SWITCH
- THE CYCLE LAMP WILL COME ON.
•
AT THE END OF THE
CYCLE THE CYCLE LAMP WILL GO OUT - OPEN THE DOOR AND PULL OUT THE BASKET.
•
ALLOW EXCESS WATER TO RUN OFF BEFORE REMOVING.
PREPARATION
•
CHECK THE
DRAIN PLUG
IS
PUSHED
FIRMLY IN PLACE AND THE
FILTER BOWL
IS POSITIONED INTO THE OUTLET HOLE.
•
CHECK THE
DETERGENT
( RED ) AND
RINSE AID
( CLEAR ) SUPPLY TUBES, WITH
FOOT VALVES
- ARE SUBMERGED IN SUFFICIENT PRODUCT.
•
CHECK THE DOOR IS CLOSED AND PRESS THE
POWER
SWITCH
- THE POWER GREEN LAMP WILL COME ON.
•
ALLOW 30 mins FOR THE MACHINE TO FILL WITH WATER AND REACH THE CORRECT WASHING TEMPERATURE.
MACHINE READY LAMP
WILL COME ON.
ROUTINE MAINTENANCE
•
AT THE END OF A SESSION TURN OFF THE
POWER SWITCH.
DO NOT REMOVE THE
FILTER BOWL
AT THIS STAGE.
•
REMOVE THE
DRAIN PLUG
- THE WASH TANK WILL EMPTY. MACHINES FITTED WITH DRAIN PUMP WILL AUTOMATICALLY START TO PUMP THE WATER OUT.
•
COLLECT THE DEBRIS AND REMOVE FROM THE WASH TANK.
•
CLEAN AROUND THE WASH TANK, DOOR SURROUNDS AND HINGES WITH AN 'ADDIS'’ TYPE WASHING UP BRUSH.
•
DO NOT USE CHLORIDE CONTAINING BASED CLEANING SOLUTIONS OR ABRASIVES WHEN CLEANING THE WASH TANK.
•
TAKE OUT THE
FILTER BOWL
- CLEAN THOROUGHLY AND REPLACE.
•
DO NOT ALLOW DEBRIS TO GO DOWN THE
OUTLET HOLE
AS THIS MAY DAMAGE YOUR MACHINE.
•
REGULARLY CHECK
RINSE JETS
AND
WASH JETS
ARE CLEAR OF DEBRIS OR LIME SCALE - REMOVE IF NECESSARY BY UNSCREWING THE
RINSE ARM NUT
THAT HOLDS THE
RINSE ARM
IN PLACE - REMOVE THE
RINSE PIN
THAT HOLDS THE
WASH ARM
IN PLACE - CLEAN BOTH THOROUGHLY AND REASSEMBLE.
WATER SOFTENER REGENERATION
•
THE
SALT LOW LAMP
WHEN ON WARNS IF THE SALT CONTAINER IS EMPTY.
•
UNSCREW THE
SALT CONTAINER LID
LOCATED INSIDE THE WASH TANK AND FILL WITH GRANULAR CATERING SALT ( THE FULL CONTAINER WILL
APPROXIMATELY REGENERATE FOUR REGENERATION CYCLES & HOLDS 1 Kg OF SALT).ENSURE THE
SALT CONTAINER LID
IS SECURE AFTER FILLING.
•
REMOVE THE DRAIN PLUG FROM THE MACHINE DURING THE REGENERATION OF THE WATER SOFTENER.
•
THE MACHINE
POWER SWITCH
MUST BE OFF TO ENABLE THE REGENERATION CYCLE.
•
CLOSE THE DOOR AND PRESS THE
REGENERATION SWITCH
. THE
WATER SOFTENER REGENERATION LAMP
WILL COME ON.
•
THE REGENERATION OF THE WATER SOFTENER WILL TAKE AROUND 20 MINUETS AND WILL BE FULLY AUTOMATIC.
•
THE
WATER SOFTENER REGENERATION LAMP
WILL GO OUT AND THE MACHINE WILL SWITCH OFF AUTOMATICALLY AFTER THE REGENERATION
CYCLE IS COMPLETE. REMEMBER TO REPLACE THE DRAIN PLUG BEFORE RE-FILLING THE MACHINE.
•
MEDIUM-WATER HARDNESS MAY REQUIRE FOUR REGENERATIONS A WEEK. MEDIUM TO HARD-WATER HARDNESS MAY
REQUIRE DAILY REGENERATION.
SALT CONTAINER
LID