manualshive.com logo in svg

DaytonAudio DSPB Series, Руководство пользователя

Поделиться
Скачать
DaytonAudio DSPB Series Скачать руководство пользователя страница 10

D.

 

DSPB - K / DSPB - KE - Quick Start 

 

1. Provide power to the micro-usb jack (J2) 

a.

 

Note 

–

 the on board micro-usb jack will 

not 

provide access to Sigma Studio if hooked up 

to a computer (but it can provide the DSPB-K power), an ICP1 is required for 
programming with SigmaStudio or app control. 

2.

 

If using a DSPB-KE, using the provided 10 pin cable, connect J1 of the DSPB-K to J4 of the DSPB-
KE

.

 

a.

 

Follow the wiring diagram to make the desired input and output connections to the 
DSPB-KE. There are many possibilities for connections, including 3.5mm, RCA, and 
headers. Each port is clearly labelled on the bottom of the board for easy connection.  

If not using the DSPB-KE, a custom solution will be required to get input and output from the 
DSPB-K. All inputs and outputs are exposed through the J2 header, and each pin has a clear label 
on the board under this header. 

3.

 

Set the switch on the DSPB-

K to ‘1’ for playback mode. 

 

4.

 

If all of the correct connections are made and power is connected, the device should be 
functioning. If not 

–

  

a.

 

Press the reset button on the DSPB-K. 

b.

 

Check the position of the potentiometers. 

c.

 

Check that your output device is functioning correctly.  

d.

 

Check the connection between the DSPB-K and DSPB-KE is secure on each board. 

e.

 

Check the 10 pin cable that connects the DSPB-K to the DSPB-KE 

f.

 

Check that your input device is functioning correctly 

g.

 

Check that the switch on the DSP-

K is set to ‘1’.

 

5.

 

Adjusting the potentiometers on the board labelled POT1-4 will allow quick adjustments without 
any programming.  

a.

 

POT1 

–

 Subwoofer Gain Control (this affects the output from J10 of the DSPB-KE, the 

sub out port) 

b.

 

POT2 

–

 Subwoofer Low Pass Frequency Adjustment  

c.

 

POT3 

–

 Stereo High Pass Frequency Adjustment 

d.

 

POT4 

–

 Stereo Gain Control 

Содержание DSPB Series
















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды